U0040: Kommunikationsbus des Fahrzeugs B — (+) niedrig
Was zu tun ist
Expect a group of systems to have stopped working together. A network wire is being held down, so messages cannot get through.
Two possibilities, and they need different work.
A damaged wire — shorted to the bodywork somewhere. Mention anything fitted to the car (a tracker, dashcam, alarm, stereo or tow bar) since an added earth beside the network wires is a common cause, and say whether the fault came and went before becoming permanent, which points at a wire rubbing through.
Or a computer holding the network down by itself. A failed module can pull the line to earth exactly as a damaged wire does, and no amount of inspecting wiring will find it. The standard way to identify it is to unplug computers one at a time until the network recovers — slow, methodical, and much faster than tracing a wire that turns out to be undamaged.
So if the wiring has been checked and proven good, that is progress rather than a dead end. It points at the second possibility.
Do not let computers be replaced before that test has actually been done, though — a long fault list is not evidence against any particular one.
Was dieser Code bedeutet
The positive line of vehicle communication bus B is being held low. See U0004 for the short-to-earth argument and U0031 for why the voltage test works before the network has been identified.
One cause is worth raising ahead of the wiring on any bus where a module has been added or replaced: a module can hold a bus down by itself.
A transceiver that has failed with its output stuck low pulls the line to earth exactly as a chafed wire does, and no amount of inspecting the harness finds it. U0100 names this among its causes and it applies with force here.
The method that separates the two is disconnection rather than measurement. Unplug modules from the network one at a time and watch the line recover — the module that restores the bus when removed is the one holding it down. That is slow, it is the standard approach, and it is much faster than tracing a conductor that is not damaged.
So a bus that stays low with the harness proven good is a module, and the ordinary wiring causes should be eliminated first only because they are cheaper to check.
Wahrscheinliche Ursachen
Hier anfangen
- Leitung mit Masse kurzgeschlossen · mittel
- Ein anderes Steuergerät zieht den Bus auf Masse · Fachwerkstatt
- Datenbusleitungen beschädigt · mittel
- Schlechte Leitungsverbindung in einem nachträglichen Einbau · mittel
Seltener
- Kabelbaum beschädigt · mittel
- Wasser in den Stecker eingedrungen · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0040.