P2620: Ausgang der Drosselklappenstellung — Stromkreis unterbrochen
Was zu tun ist
The engine will respond to the accelerator exactly as normal. The problem shows up in the gearbox: changes at the wrong moments, hunting between gears, and most obviously kickdown that no longer works — flooring the pedal gives you a responsive engine and no downshift.
That combination is the important thing to report, because it points away from the transmission itself. The engine module knows exactly where the throttle is — it is proving that every time you accelerate — and the fault is that the message is not reaching the transmission module. A transmission that is stripped, rebuilt or replaced on the strength of this will behave identically afterwards. Ask for the wiring between the two modules to be checked, and for the transmission module's own view of throttle position to be compared with the engine module's on a scan tool. That takes minutes and settles it.
Was dieser Code bedeutet
An open circuit on the output by which the engine module passes throttle position to another module.
The same inversion as the rest of this family — this is a signal being sent, not read — and the same exoneration follows: the throttle position sensor, the throttle body and the accelerator pedal are all working, because the module had a value to pass on.
What receives it is almost always the transmission, and that makes the symptom specific and recognisable. An automatic transmission decides when to change gear largely from how far the throttle is open and how quickly it moved: a light throttle asks for an early, gentle upshift; a sudden wide opening asks for a downshift and a hard hold. Take that information away and the transmission is left guessing.
So the presenting complaint is a gearbox one, and it is worth recognising because it gets gearboxes stripped. Shifts happen at the wrong points, the transmission hunts between gears, and — the clearest single sign — kickdown stops working: flooring the pedal produces a willing engine and no downshift, because the module that would have ordered the downshift never learned the pedal moved.
The cheapest thing anyone can do with this code is notice that the engine responds perfectly to the throttle while the transmission behaves as though it does not. That gap is the diagnosis.
Wahrscheinliche Ursachen
Hier anfangen
- Leitungsbruch in der Sensorleitung · mittel
- Korrodierter oder loser Stecker · einfach
- Kabelbaum beschädigt · mittel
Seltener
- Eingang des empfangenden Steuergeräts defekt · Fachwerkstatt
- Getriebesteuergerät defekt · Fachwerkstatt
Selten
- Motorsteuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2620.